Hallo!!!
Auf dem Pannel einer gebraucht gekauften I520 erschein C1001020. Mann kann am Pannel gar nichts mehr verstellen. Sie geht nicht an und nichts passiert! Den Serviceprozessor habe ich schon resetted, ohne Ergebnis. Hat jemand eine Lösung, oder schon mal das gleiche Problem!
MFG Dr. Cult
AS400.lehrling
30-04-10, 13:49
Probier das mal
FSPSP02
This procedure is for boot failures that terminate very early in the boot process.
Attention: The system firmware level should be periodically checked on all servers and if it is appropriate, the firmware should be updated to the latest level. If you were directed here because the server displayed B1817201, C1001014, or C1001020 or a combination of these codes, the latest level of firmware can help avoid a recurrence of this problem.Even if the customer cannot update the firmware on this system at this time, all of their systems should be updated to the latest firmware level as soon as possible to help prevent this problem from occurring on other systems.
Do one of the following:
If the system has a physical control panel, continue to Systems with a physical control panel (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/fspsp02.htm?resultof=%22%43%31%30%30%31%30%32%30%2 2%20%22%63%31%30%30%31%30%32%30%22%20#fspsp02__wip hycontpnl).
If the system does not have a physical control panel, go to Systems with no physical control panel (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/fspsp02.htm?resultof=%22%43%31%30%30%31%30%32%30%2 2%20%22%63%31%30%30%31%30%32%30%22%20#fspsp02__wop hycontpnl).
Systems with a physical control panelThis error path is indicated when the SRC data words are scrolling automatically through control panel functions 11, 12, and 13, and the control panel interface buttons are not responsive.Perform the following:
Push the white power button to reset the system and bring it up on the other side of platform LIC. Note: The white power button will only reset the system and attempt to reach standby.
Did an SRC occur after bringing the system up on the other side?
No: Update the code on the other side by performing symbolic FRU LICCODE (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/fruliccode.htm#fruliccode). This ends the procedure.
Yes: Continue with the next step.
Is the SRC the same SRC that brought you to this procedure?
No: Return to Start of call procedure (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/starthere.htm#starthere) to service this new SRC. This ends the procedure.
Yes: Perform the following:
Replace the service processor using symbolic FRU SVCPROC (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/frusvcproc.htm#frusvcproc).
If the problem persists, replace the system backplane using symbolic FRU SYSBKPL (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/frusysbkpl.htm#frusysbkpl). This ends the procedure. Systems with no physical control panelIf the service processor fails very early in the boot process, the logical control panel on the HMC will not be available. In that case, use the UEPO switch to completely remove power from the system, then restore power and watch the HMC to see if the logical control panel is available.
If the HMC still says that it cannot communicate with the managed system after the power is cycled, replace the service processor using symbolic FRU SVCPROC (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/frusvcproc.htm#frusvcproc). This ends the procedure.
If the HMC can communicate with the managed system after the power is cycled, open the logical control panel and look for the service processor to reach standby. If the service processor reaches standby, this ends the procedure. If it does not reach standby, replace the service processor using symbolic FRU SVCPROC (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/frusvcproc.htm#frusvcproc). This ends the procedure.
Parent topic: Service processor isolation procedures (http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/topic/iphau_p5/pipsp.htm)
Gruß AS400.lehrling
Hallo,
ich denke da fehlt Dir ein Ptf:
IBM - MB01803 - RFSP: PERSISTENT C1001020 AFTER UNGARDING FSP (http://www-01.ibm.com/support/docview.wss?uid=nas2491a8fdacbf7603b862571a3003c73 4d)