View Full Version : Maschine zurücksetzen - Zurücksenden an Leasinggeber
Hallo Leute,
wir haben eine alte I5 V5R4 die wir unseren Leasinggeber zurücksenden müssen.
Natürlich formatiert geputzt und küsschen drauf.
Nachdem ich jetzt noch nicht soooo viele ISeries zurückgesetzt habe (derzeit 0) würde ich gerne wissen wie ich dass am geschicktesten anstellen sollte.
Lizenzprogramme sind natürlich alle abgleaufen und der QSECOFR ist schonmal garnicht anmeldbar. (wg. den abgelaufenen Systemprogrammen)
DST komm ich drauf.
Soweit ich weiß reicht hier über das DST die Platten einfach zu formatieren.
Ok so hab ichs gemacht:
1) System iOperations Console geöffnet -> Verbindung hergestellt zur Fernen Konsole
2) IPL mit Ferner Steuerkonsole gemacht (Manuell -> Auswahl 03 Start IPL)
3) Bei der Anmeldung DST-Auswahl getroffen (1. IPL ...x-DSP Starten)
4) - Beim Anmeldescreen F5 gedrückt um das QSECOFR (SST) PW zu ändern
5) DST -> 4. Work with disk units -> 2. Work with disk unit recovery -> 10. Delete disk unit data
No Non-Configured Units
The function you requested cannot be performed at this time
because:
o The requested function requires one or more non-configured
units. No non-configured units were found on the system.
This condition must be corrected before the requested function
can be performed.
The following are the recommended recovery procedures:
o If there are non-configured units connected to the system,
ensure that all such units are powered on and are cabled
correctly. If all non-configured units are powered on and
are cabled correctly and this error still occurs, call for
service.
=> Display Disk Configuration Status
Serial Resource Hot Spare
SP Unit Number Type Model Name Status Protection
1 Unprotected
1 68-0F73F43 4328 070 DD004 RAID 5/Active N
2 68-0F67706 4328 074 DD002 RAID 5/Active N
3 68-0812767 4328 074 DD005 RAID 5/Active N
4 68-0F4DE6C 4328 074 DD001 RAID 5/Active N
5 68-0F31119 4328 074 DD003 RAID 5/Active N
:confused: Und nu?? Leider kann man hier nix formatieren..
Quell: http://www.code400.com/forum/showthread.php/595-How-to-clear-an-Iseries
Hallo,
ich würde dieses IBM Dokument nehmen:
Document Title
Initialize Disk Drives So That All Data Is Erased Off of a System
Document Description
In some cases, a customer may wish to erase all data off their system. They may want to do
this because they are getting rid of it and do not want any of their data on it.
No Partitions:
The procedure for doing this follows:
1 Do a D Manual IPL using a SAVSYS, full system save, or LIC Install CD.
2 The first menu will give an Option 1 to Install LIC, and Option 2 to use DST. Select Option 1.
3 The Install LIC menu will provide 5 options. Select Option 2 to Install Licensed Internal Code and Initialize System.
4 After the install of LIC is complete, the system will IPL to the DST primary menu.
5 Configure all the disk drives by adding them into system ASP (ASP1).
This writes zeroes on the disk drives so only the LIC is loaded.
o Select Option 3 - Use DST.
o Work with Disk Units.
o Work with Disk Configuration.
o Work with ASP Configuration.
o Add units to ASPs.
o Type 1 in front of all the available units.
6 When that is complete, power off the system by pressing the power button two times.
System is clean and ready to go.
Partitioned System:
(This will remove all partitions and erase all data on drives from all earlier partitions.)
The procedure for doing this follows:
1 Do a D Manual IPL using a SAVSYS, full system save, or LIC Install CD of the primary partition.
2 The first menu will give an Option 1 to Install LIC, and Option 2 to use DST. Select Option 1.
3 The Install LIC menu will provide 5 options. Select Option 2 to Install Licensed Internal Code and Initialize System.
4 After the install of LIC is complete, the system will IPL to the DST primary menu.
5 Take the option to Work with system partitions.
6 Take the option to Recover configuartion data.
7 Take the option to Clear non-configured disk unit configuration data.
8 Exit back to the DST primary menu.
9 Configure all the disk drives by adding them into system ASP (ASP1).
This writes zeroes on the disk drives so only the LIC is loaded.
o Select Option 3 - Use DST.
o Work with Disk Units.
o Work with Disk Configuration.
o Work with ASP Configuration.
o Add units to ASPs.
o Type 1 in front of all the available units.
10 When that is complete, power off the system by pressing the power button two times.
System is clean and ready to go