-
A5 mit Host Print Transform auf HP
Hat jemand erfahrungen mit DIN A5 Ausdrucken über Host Print Transform?
Seit Tagen kämpfe ich mit HPT und der A5 Papierzuführung auf einem HP 1320n und HP 5020tn.
Der 1320n trifft das Papier nicht:
In der DEVD ist beim Papierfach A5 eingestellt.
Es sieht beim Ausdruck über HPT (90 Grad Seitendrehung) ungefähr so aus:
Code:
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
+----------------------------------------------------+
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx |
| |
| |
| |
| |
| |
+----------------------------------------------------+
Auf allen Infoprintern stimmt der Ausdruck 100%ig
Der 5020tn bringt die Meldung:
Normal EXEC in Fach 1 einlegen.
hat jemand einen Rat woran das liegen kann?
merci.
Dirk
-
Im WSCST ist die Papiergröße für ein Fach anzugeben und dann dieses Fach anzusteuern:
Drawer Page Size
The DWRPAGSIZ (drawer page size) tag defines the size of the paper present in a
specific source paper drawer.
In raster mode, this paper size is used to allocate the raster page buffer. The SCS
to ASCII transform uses this paper size to determine if COR mode is required.
If the drawer size is not defined, the host print transform uses the page size that is
specified in the AS/400 print job.
You can define a drawer size for one or more of the source drawers. You begin
support for the drawer page size with the DWRPAGSIZ tag and end the support
with the EDWRPAGSIZE tag. The DWRPAGSIZE tags fall between, defining a
drawer and its size.
Using the drawer page size tags, your source could look something like this for a
printer supporting two different source drawers.
:DWRPAGSIZ.
:DWRPAGSIZE...
:DWRPAGSIZE...
:EDWRPAGSIZ.
The following sections describes the tags used to support different drawer sizes.
Drawer Page Size (DWRPAGSIZ) Tag
The DWRPAGSIZ tag defines the page size for a source drawer. This tag must be
followed by one or more DWRPAGSIZE tags that contain the drawer size. There
are no parameters on this tag. The syntax is:
:DWRPAGSIZ.
Drawer Page Size Entry (DWRPAGSIZE) Tag
The DWRPAGSIZE tag defines the page size for a particular source drawer. The
DWRPAGSIZ tag must be follows by one or more DWRPAGSIZE tags. The
EDWRPAGSIZE tag must follow a group of DWRPAGSIZE tags. The syntax is:
:DWRPAGSIZE
DRAWER = 0-255
PAGWTH = Page width
PAGLEN = Page length.
DRAWER
This is a required parameter. This parameter defines the source drawer.
0 The envelope drawer is specified.
1-255 The drawer 1-255 is specified.
PAGWTH
This is a required parameter. This parameter specifies the drawer page width in
1/1440 inch increments. This value must be an integer. The width is the
left-to-right dimension of a piece of paper.
PAGLEN
This is a required parameter. This parameter specifies the drawer page length
1/1440 inch increments. This value must be an integer. The width is the
top-to-bottom dimension of a piece of paper.
End Drawer Page Size (EDWRPAGSIZ) Tag
The EDWRPAGSIZ tag is used to end a group of drawer page size entries in the
customizing source. There are no parameters on this tag. The syntax is:
:EDWRPAGSIZ.
-
Danke für die Antwort.
Da die Spoolfile ein Overlay enthält, das relativ zum Text richtig positioniert wird, glaube ich leider nicht, dass es an der Seitengrößensteuerung liegt...
Wenn ich in der Lan-Device den Parameter PPRSRC1 auf A4 ändere schaut der Ausdruck auch ganz anders aus als mit A5. Also die Seitengrößensteuerung von HPT funktioniert soweit.
-
-
Ich habe mir noch mal die ESC-Sequenzen angeschaut.
Ich glaube hier liegt ein Fehler in den WSCST von IBM vor.
In allen *HP... WSCST-Objekten steht bei PAGSIZ für A5:
Code:
:PAGSIZE
PAGWTH= 8352
PAGLEN=11952
DATA ='1B266C303141'X.
Und das bedeutet Executive (ASCII Esc & / 0 1 A).
Das ist ja auch deine Fehlermeldung am Drucker.
Korrekt wäre für A5 (ASCII Esc & / 2 5 A), also :
Code:
:PAGSIZE
PAGWTH= 8352
PAGLEN=11952
DATA ='1B266C323541'X.
PCL-Referenz :
http://h20000.www2.hp.com/bc/docs/su...5/bpl13205.pdf
Bitte mal korrigieren und dann erneut probieren.
Trotzdem die Frage, welches WSCST hast du für den Infoprint und welches für den HP-Drucker ausgewählt.
Könnte aber auch sein, das das so eingestellt wurde, weil nicht alle HP-Drucker auch A5 unterstützen.
Wobei die 4000er Serie z.B. A5 unterstützt, aber das WSCST-Objekt trotzdem falsch ist.
Siehe (nach A5 suchen bzw. Tabelle 1-1 ):
http://lprng.sourceforge.net/DISTRIB...S/pcl5comp.pdf
Similar Threads
-
By muadeep in forum NEWSboard Drucker
Antworten: 10
Letzter Beitrag: 01-10-07, 21:32
-
By marmart in forum IBM i Hauptforum
Antworten: 5
Letzter Beitrag: 25-09-07, 15:29
-
By schnorkel in forum NEWSboard Drucker
Antworten: 8
Letzter Beitrag: 18-09-06, 16:58
-
By luis in forum NEWSboard Drucker
Antworten: 6
Letzter Beitrag: 03-03-05, 07:31
-
By Nötzli in forum NEWSboard Drucker
Antworten: 5
Letzter Beitrag: 22-10-04, 11:32
Berechtigungen
- Neue Themen erstellen: Nein
- Themen beantworten: Nein
- You may not post attachments
- You may not edit your posts
-
Foren-Regeln
|
Erweiterte Foren Suche
Google Foren Suche
Forum & Artikel Update eMail
AS/400 / IBM i
Server Expert Gruppen
Unternehmens IT
|
Kategorien online Artikel
- Big Data, Analytics, BI, MIS
- Cloud, Social Media, Devices
- DMS, Archivierung, Druck
- ERP + Add-ons, Business Software
- Hochverfügbarkeit
- Human Resources, Personal
- IBM Announcements
- IT-Karikaturen
- Leitartikel
- Load`n`go
- Messen, Veranstaltungen
- NEWSolutions Dossiers
- Programmierung
- Security
- Software Development + Change Mgmt.
- Solutions & Provider
- Speicher – Storage
- Strategische Berichte
- Systemmanagement
- Tools, Hot-Tips
Auf dem Laufenden bleiben
|
Bookmarks